verilog homework help

Boost your journey with 24/7 access to skilled experts, offering unmatched verilog homework help

Trusted by 1.1 M+ Happy Students

4.4Trust Pilot

4.4Edu Reviewer

5App Review

4.8Student

4.2Sitejabber

Recently Asked verilog Questions

Expert help when you need it

Q1:You have to submit: • Truth table input from 0000 to 1111. • K-map • Verilog Code. • Waveform See Answer
Q2:Level 2 - Design of an 8bit+8bit BCD Adder You task is to design an BCD adder, that adds two two-digit BCD numbers. The structure of a 4bit BCD adder is as follows: carry out Sum > 9? carry out binary adder binary adder Sum carry in t • Design your BCD adder in VHDL; this must be structural for the top-level • Simulate your design and show correct behaviour; the input and output vectors must be shown in decimal Your submission must include the following: • ALL VHDL sources • All simulation screenshotsSee Answer
Q3:2: Construct timing diagram [5 points] Graph the signals that result for the circuit you drew for Step 1 of the prelab. Assume that the propagation delay is much shorter than the step size of 1 second per division. In other words, when an input causes an output transition, you will see it at the same time as the signal that caused the transition. You should also assume that the initial state of the Q output of the flip-flop is 0.See Answer
Q4:4: Instantiate structural flip-flops in Verilog [10 points] Next, you will simulate a ring counter using Verilog. Let's do so in a manner more similar to how you will construct your lab experiment. In your lab experiment, you will use two 74HC74 dual-D-type flip-flops. Each of these chips contains two flip-flops. Each of those flip-flops has an active-low asynchronous reset (also called "clear") and an active-low asynchronous set (also called "preset"). Although a Verilog simulator can model any kind of logic, the Verilog simulator is strictly limited to disallow anything not supported by the FPGA we use for the class. Our simulator will not allow a flip-flop with both a reset and a set, since it is not supported by our FPGA. Each flip-flop can only have either a reset or a set. We will use the two models provided for the 74HC74 in the course References directory. One of them has an active-low reset 'rn' and the other has an active-low set 'sn'. Each one has 'd', 'c', 'q', and 'qn' lines for the data input, clock input, Q output and inverted output, respectively. You can see the implementation of these modules as well. For this exercise, create a new simulator workspace named "lab7". Rename the default file tab from "template.sv" to "prelab7.sv". Start with the standard top module provided by the simulator. Append the module definitions for hc74_reset and hc74_set below top. In the top module, create an instance of hc74_reset and connect its clock to pb[0], connect its data input to pb[1], and connect its non-inverted output (q) to right[0]. Connect its active-low asynchronous reset (rn) to the 'W' button (pb[16]). Use <shift>-click to press and hold the 'W' button to make sure pb[16] is high. With this, you have a system where the right[0] LED illuminates after a rising edge of the clock (0 button) when the '1' button is held down. If the right[0] is on, it is cleared the instant the 'W' button is released. This is the nature of an active-low reset.See Answer
Q5:1. Write Behavioral Verilog code (using case statements) for the following sub-modules: a. 4-to-1 multiplexer b. 8-to-1 multiplexer Once you've written both modules, create blocks from the code. In order to write the modules properly for a symbol block, each input and select line must be declared independently. Inside the Verilog module, combine the select lines and inputs into a bus (e.g. a wire with multiple bits). An example of this type design for a 2-to-1 multiplexer is given below.See Answer
Q6:2. Create a full adder as a logic diagram using only 4-to-1 multiplexers and NAND gates. Use the 4- to-1 multiplexer blocks that you designed in problem #1. Use Cin as select line 1 and X as select line 0.See Answer
Q7:3. Create a full adder schematic with your block from problem #2 and the input/output pins X,Y, Cin, Cout, S. Perform a waveform drawing showing the outputs for all possible input values. Show the output of your drawing, demonstrating that it works correctly as a full adder.See Answer
Q8:4. Create the function F(A, B, C, D) = ABC' + C'D' + BCD + A'B'D + AB'D' using an 8-to-1 multiplexer and only NOR gates on the front-end. As select lines, use S₂ = C, S₁ = D, So = A. Use the 8-to-1 multiplexer block you designed in problem #1.See Answer
Q9:5. Perform a waveform drawing on your circuit from Problem #4 and show the outputs for all possible input values.See Answer
Q10:Given the input waveforms shown in Fig. 1, sketch the output, Q, of an SR latch.See Answer
Q11:You have to submit: • Truth table input from 0000 to 1111. • K-map • Verilog Code. • Waveform See Answer

TutorBin Testimonials

I found TutorBin Verilog homework help when I was struggling with complex concepts. Experts provided step-wise explanations and examples to help me understand concepts clearly.

Rick Jordon

TutorBin experts resolve your doubts without making you wait for long. Their experts are responsive & available 24/7 whenever you need Verilog subject guidance.

Andrea Jacobs

I trust TutorBin for assisting me in completing Verilog assignments with quality and 100% accuracy. Experts are polite, listen to my problems, and have extensive experience in their domain.

Lilian King

I got my Verilog homework done on time. My assignment is proofread and edited by professionals. Got zero plagiarism as experts developed my assignment from scratch. Feel relieved and super excited.

Joey Dip

Popular Subjects for verilog

You can get the best rated step-by-step problem explanations from 65000+ expert tutors by ordering TutorBin verilog homework help.

TutorBin helping students around the globe

TutorBin believes that distance should never be a barrier to learning. Over 500000+ orders and 100000+ happy customers explain TutorBin has become the name that keeps learning fun in the UK, USA, Canada, Australia, Singapore, and UAE.