microwave devices homework help
Boost your journey with 24/7 access to skilled experts, offering unmatched microwave devices homework help
Trusted by 1.1 M+ Happy Students
Recently Asked microwave devices Questions
Expert help when you need it- Q1:14. Plot the following impedance points on smith chart. i. Z1= 100+j50 ii. Z2 = 75-j100 iii. Z3 = j200 iv. Z4 = 150See Answer
- Q2:In the given figure 2, simulated and measured S11 plots of an antenna designed are given. i. Simulated without defected ground structure (DGS), ii. simulated with DGS, iii. Measured with DGS. State the impedance bandwidth of these three S11 plots and the points where resonances occur in each plot. 13. $11 (dB) -10 -20 -30 -40 24 26 28 Simulated without DGS Simulated with DGS -Measured with DGS 30 32 Frequency (GHz) Figure2: S11 vs. frequency plot of the antenna. 34 36 38 40See Answer
- Q3:6. Find the characteristic impedance Zo of the lossless transmission line whose unit length of inductance L = 10 mH and unit length of capacitance C = 200 μF.See Answer
- Q4:In the figure 1 given below, determine the frequency range where the antenna efficiency is above 80%. And state the frequency where antenna gain isSee Answer
- Q5:14. Plot the following impedance points on smith chart. i. Z1= 100+j50 ii. Z2 = 75-j100 iii. Z3 = j200 iv. Z4 = 150See Answer
- Q6:15. Plot the following on smith chart i. Z5 = infinity (Open circuit) ii. Z6 = 0 (short circuit) iii. Z7 = 50 (Z.) iv. Z8 = 184-j900See Answer
- Q7:EXPERIMENT 5 • Measurement of Impedance (Use component #507 - termination - as an additional load): Please do the following: 1. Record all your work in your individual lab notebook in an orderly fashion. 2. Write a group formal report in which all group/team members participate fully. Use the formal lab report format provided! Your report must address all the questions, objectives, etc. in the handout. Please DO NOT forget RESULTS and CONCLUSIONS!See Answer
- Q8:11 The load impedance (ZL) of 60- j80 Q terminates a transmission line with a characteristic impedance (Zo) of 50 Q. A parallel short-circuited stub is used to match the line to its load. Use the Smith Chart to calculate: a) the normalised load impedance, load reflection coefficient |L|, voltage- standing-wave-ratio (VSWR), b) normalised load admittance (YL), stub admittance (y2), c) the distance of the stub from the load 'd', d) length of the stub 'L'. matched line (y,+ y₁ =1) 32=jb y₁ =1-jb [5] [5] [5] [5]See Answer
- Q9:1. If a signal has a gain (G) equals to 32000 (linear), what is the gain in dB? How much will be the remaining power (in %), if the gain is reduced to 6dB.See Answer
- Q10:4. An amplifier has an input power of 0.5 watts and its output power of 75 watts. What is the gain of the amplifier in dB?See Answer
- Q11:5. Calculate the length of a quarter-wave transmission line where frequency is 1800 MHz.See Answer
- Q12:7. Calculate the gain of the antenna (in dB) if the radiation resistance of the antenna is 52 £2, and loss resistance is 12 2. The antenna directivity is 18 (linear).See Answer
- Q13:8. Calculate the radiation resistance when the loss resistance of an antenna is 82, the directivity of the antenna is 20 (linear) and power gain is 18 (linear).See Answer
- Q14:9. If the reflection coefficient (r) is 0.5, calculate the VSWR.See Answer
- Q15:10. Calculate the reflection coefficient || when the antenna load impedance is Z₁ = (30 + j 40), and characteristic impedance is Z. = 50 Ω.See Answer
- Q16:11. Calculate the reflection coefficient when the VSWR= 1.5. Also calculate the corresponding return loss in dB.See Answer
- Q17:In the figure 1 given below,determine the frequency rangewhere the antenna efficiency is above 80%.And state the frequencywhere antenna gain is maximum in the plot.一-.E重k起成y70如2241o9达yGlu)Figurel:Gain and efficiency vs.frequency plot.See Answer
- Q18:In the figure 2, simulated and measured S11 plots of an antenna designed are given. 1. SimulatedSee Answer
- Q19:14. Plot the following impedance points on smith chart. i. Z1= 100+j50 ii. Z2 = 75-j100 iii. Z3 = j200 iv. Z4 = 150See Answer
- Q20:15. Plot the following on smith chart i. Z5 = infinity (Open circuit) ii. Z6 = 0 (short circuit) iii. Z7 = 50 (Z.) iv. Z8 = 184-j900See Answer
TutorBin Testimonials
I found TutorBin Microwave Devices homework help when I was struggling with complex concepts. Experts provided step-wise explanations and examples to help me understand concepts clearly.
Rick Jordon
5
TutorBin experts resolve your doubts without making you wait for long. Their experts are responsive & available 24/7 whenever you need Microwave Devices subject guidance.
Andrea Jacobs
5
I trust TutorBin for assisting me in completing Microwave Devices assignments with quality and 100% accuracy. Experts are polite, listen to my problems, and have extensive experience in their domain.
Lilian King
5
I got my Microwave Devices homework done on time. My assignment is proofread and edited by professionals. Got zero plagiarism as experts developed my assignment from scratch. Feel relieved and super excited.
Joey Dip
5
Popular Subjects for microwave devices
You can get the best rated step-by-step problem explanations from 65000+ expert tutors by ordering TutorBin microwave devices homework help.- Analog Electronics
- Arduino
- Basic Electronics
- Verilog
- Matlab And Simulation
- Microprocessor and Microcontroller
- Communications
- CPUIator
- OrCAD
- Photonics
- Xilinx
- Proteus
- CodeWarrior
- Electronics Devices
- Embedded System
- Instrumentation
- Microwave Devices
- Antenna Theory
- Logic Circuits/Vlsi
- TinkerCAD
- Virtuoso
- Image Processing
- Signal Processing
- Symica
- Network Analysis And Synthesis
- Signals And Systems
- Soft Computing
TutorBin helping students around the globe
TutorBin believes that distance should never be a barrier to learning. Over 500000+ orders and 100000+ happy customers explain TutorBin has become the name that keeps learning fun in the UK, USA, Canada, Australia, Singapore, and UAE.
