Search for question
Question

Executive Summary Submission

Prototype Activity Report

Must summarize the information in the document. indicate what risks were addressed, the mitigation strategy, the results, and resulting changes to the project

Fig: 1


Most Viewed Questions Of Communications

9. If a GSM timeslot consists of 6 trailing bits, 8.25 guard bits, 26 training bits, and 2 traffic bursts of 58 bits of data. Find the total number of bits in each time slot. If a frame has 8 slots, find the total number of bits in each frame, also calculate overhead bits in each frame and frame efficiency.


A DSB-SC AM signal is modulated by the signal m(t)=2 \cos 2000 \pi t+\cos 6000 \pi t . The modulated signal is u(t)=100 m(t) \cos 2 \pi f_{c} t \text { where } f_{c}=1 \mathrm{MHz} 1. Determine and sketch the spectrum of the AM signal. 2. Determine the average power in the frequency components.


5.2-3 In a satellite radio system, 500 stations of stereo quality are to be multiplexed in one data stream. For each station, two (left and right) signal channels each of bandwidth 15,000 Hz are sampled, quantized, and binary-coded into PCM signals. (a) If the maximum acceptable quantization error in sample amplitudes is 1% of the peak signal voltage, find the minimum number of bits needed for a uniform quantizer. (b) If the sampling rate must be 8% higher than the Nyquist rate, find the minimum bit rate of the multiplexed data stream based on the quantizer of part (a). (c) If 2% more bits are added to the multiplexed data for error protection and synchronization, determine the minimum bandwidth needed to transmit the final data stream to receivers.


5.6-1 A DM system has input message signal m(t)=50 e^{-200 t} \cos 1000 \pi t \cdot u(t) (a) Determine the minimum step size E necessary to avoid DM slope overload. (b) Calculate the minimum average quantization noise power based on part (a).


The message signal m(t) has the Fourier transform shown in Figure P-3.11(a). This signal is applied to the system shown in Figure P-3.11(b) to generate the signal y(t). 1. Plot Y (f), the Fourier transform of y(t). 2. Show that if y(t) is transmitted, the receiver can pass it through a replica of the system shown in Figure P-3.11 (b) to obtain m(t) back. This means that this system can be used as a simple scrambler to enhance communication privacy.


(a) Find IpsQ (- (b) Determine the width-to-length ratio of the transistor =) What is the required dc value of the input voltage (d) Find the value of resistance R. Problem 1. Consider the circuit in Figure 1. The transistor parameters are VTn = 0. 6 V,kn = un Cox =100 u/a v2 and r=0 infinity such that the small signal voltage gain is A, = 0. 85.= 100 µA/V² and ro = infinity . The circuit is to be designed such that V DSQ 1025 v and such that the small voltage gain is A v = 0.85


Problem 4: For the common-gate circuit in Figure 4, the NMOS transistor parametersare: VTn = 1 V, Kn = 3 mA/V², and 1 = 0.(12 points) (a) Determine Ipso and VDsą (3 (b) Calculate gm and ro (c) Find the small-signal voltage gain (d) Find the value of resistance R,


11. Assuming the logic gate shown below is ideal, estimate the power consumption of this circuit. (Please ignore the power consumption of the gates due to their connections to power supplies).


Consider the message signal m(t) = 20 cos(2át) volts, and carrier c(t) = 50 cos(100nt) volts.a. Sketch the resulting AM wave for 75 percent modulation (DSB-LC).b. Find the power developed across a load of 100 ohm due to this AM wave.


1) Assume x is a real Gaussian random variable with zero mean and o? variance a. Write the probability density function (PDF) of the x b. Write the PDF of the random variable y = a x + b where a and b are two deterministic real values.